ass日本风韵熟妇pics男人扒开女人屁屁桶到爽|扒开胸露出奶头亲吻视频|邻居少妇的诱惑|人人妻在线播放|日日摸夜夜摸狠狠摸婷婷|制服 丝袜 人妻|激情熟妇中文字幕|看黄色欧美特一级|日本av人妻系列|高潮对白av,丰满岳妇乱熟妇之荡,日本丰满熟妇乱又伦,日韩欧美一区二区三区在线

噴霧機噴桿有限元模態分析與結構優化
CSTR:
作者:
作者單位:

作者簡介:

通訊作者:

中圖分類號:

基金項目:

國家公益性行業（農業）科研專項資助項目（201203025-04）、江蘇省科技支撐計劃資助項目（BE2011334）,、國家農業科技成果轉化資金資助項目（2012GB2C100154）,、江蘇省高校自然科學研究重大資助項目（10KJA470007）和江蘇省高校優勢學科建設工程資助項目（蘇財教（2011）8號）


Finite Element Modal Analysis and Structure Optimization of Spray Boom
Author:
Affiliation:

Fund Project:

  • 摘要
    • |
  • 圖/表
    • |
  • 訪問統計
    • |
  • 參考文獻
    • |
  • 相似文獻
    • |
  • 引證文獻
    • |
  • 資源附件
    • |
  • 文章評論
    摘要:

    在ANSYS中建立了噴桿的參數化有限元模型，并驗證了模型的準確性。根據噴桿的模態分析結果在ANSYS中對噴桿結構進行了優化，在質量增加8.4%的情況下，噴桿一階固有頻率從9.16Hz增加到了10.41Hz,，避開了路面激勵的頻率區間。結合ADAMS對噴桿優化前,、后作業時的彈性變形作了對比,，結果表明：優化前噴桿末端在水平方向最大彈性變形Dbmax為39.6mm，均方根為12.6mm,；優化后噴桿在水平方向最大彈性變形Damax為10.1mm,，均方根為2.9mm,，噴桿經過優化后其水平方向彈性變形明顯減小。

    Abstract:

    In order to study dynamic characteristic of spray boom, a parametric finite element model of spray boom was built in ANSYS, and the model was validated by experimental modal analysis. According to the result of spray boom modal analysis, the structure of the spray boom was optimized in ANSYS, in the condition of increasing the spray boom mass for 8.4%, increasing the first mode frequency from 9.16Hz to 10.41Hz, and avoiding from the resonance vibration section. Then, the deformation of the spray boom in operating before and after optimization was compared and analyzed in ADAMS. The result showed that the max horizontal deformation at the spray boom end before optimization Dbmax was 39.6mm, and the root-mean-square was 12.6mm. The max horizontal deformation at the spray boom end after optimization Damax was 10.1mm, and the root-mean-square was 2.9mm. The horizontal deformation was reduced.

    參考文獻
    相似文獻
    引證文獻
引用本文

邱白晶,何耀杰,盛云輝,尹振華,鄧武清.噴霧機噴桿有限元模態分析與結構優化[J].農業機械學報,2014,45(8):112-116,105. Qiu Baijing, He Yaojie, Sheng Yunhu, Yin Zhenhua, Deng Wuqing. Finite Element Modal Analysis and Structure Optimization of Spray Boom[J]. Transactions of the Chinese Society for Agricultural Machinery,2014,45(8):112-116,105.

復制
分享
文章指標
  • 點擊次數:
  • 下載次數:
  • HTML閱讀次數:
  • 引用次數:
歷史
  • 收稿日期:2013-09-10
  • 最后修改日期:
  • 錄用日期:
  • 在線發布日期: 2014-08-10
  • 出版日期:
文章二維碼